Also discover our latest Design Guide for GORE® Acoustic Vents

How GORE® Portable Electronic Vents help solve the dual design challenges of preserving acoustic sound quality and device reliability.
Cross-section of remote speaker microphone

Cross-section of remote speaker microphone

The challenge of designing electronic devices that stay protected from dust, liquids and pressure becomes increasingly difficult when acoustics are introduced.

To enable sufficient sound transmission, devices require apertures. But these apertures that let the sound out also allow dust and liquids to enter the device and create performance and reliability issues. Creating clear crisp sound while protecting device reliability requires careful design of the cavities in front of and behind all transducers.

Evaluating Design Options for the Front Cavity

Open apertures provide unimpeded sound, but provide no protection from dust, liquids or immersion — hazards that nearly all portable electronics encounter. Designs with open apertures are highly susceptible to component failures, decreased device life and consumer perceptions of poor quality.

Waterproof transducers that seal the front cavity from the device prevent water and dust contamination from reaching components. But, waterproof transducers still allow water and particulates onto and around the transducer surface, which degrades acoustic performance an “acoustic penalty” by providing lower overall acoustic quality and requiring increased drive power levels to operate the transducer.

Increased pressure creating transducer bias

Increased pressure creating transducer bias

Non-porous covers such as urethane, silicone or PEEK can be used to cover apertures when immersion protection is needed. They can allow satisfactory sound transmission while protecting the transducer from dust and liquid submersion. However, these materials do not breathe. When pressure in the front cavity builds (due to temperature or altitude changes), the pressure on the compliant surfaces of the transducer increases. This pressure creates transducer bias that can significantly degrade sound quality and transducer performance.

GORE® Acoustic Vents for immersion applications provide the optimal solution for the challenges of designing front cavities. The ePTFE membrane in Gore’s immersion vents protects the transducer and the device from dust and liquid immersion up to IP68. Our highly breathable ePTFE membrane rapidly equalizes pressure in the front cavity, continuously providing exceptional acoustic performance in all designed conditions.


Additional Considerations for Dust and Splash Protection

Particulates entering through a woven mesh

Particulates entering through a woven mesh

Woven mesh covers are a partial solution, in that they can protect an aperture from liquid splash, spray or rain. However, these products consist of a single-layer grid and spacing pattern with a defined hole size. So any dust particles smaller than the defined hole size will pass through the screen and deposit on the transducer, or they will propagate through the device, potentially causing catastrophic device failure.

 

 

 

Properly designed products protect from dust, water, pressure, and transmit highquality sound

Properly designed products protect from dust, water, pressure, and transmit highquality sound

GORE® Acoustic Vents for dust and splash applications provide added protection because of their non-woven structure. While they reliably repel liquid splash, spray or rain exposure, they also offer greater protection from small particles. Gore’s expertly engineered non-woven materials provide a tortuous path that more effectively traps smaller particulates. This added protection reduces quality issues and improves device functionality.

Evaluating Design Considerations for the Back Cavity

Transducer bias created by pressure on compliant surfaces

Transducer bias created by pressure on compliant surfaces

Sealed housings protect electronic devices by providing a barrier against water or dust. But as electronic devices operate they generate heat, causing internal temperatures to increase and pressure to build inside the housing. Internal pressure can also change rapidly if the device is exposed to sudden changes in environmental temperatures or altitudes. These internal pressure changes put significant stress on the housing seals. Over time this leads to failed seals, which then allow water and contaminants to enter the device.

Properly designed products protect from dust, water, pressure, and transmit highquality sound

Properly designed products protect from dust, water, pressure, and transmit highquality sound

GORE® Pressure Vents are specifically engineered for back cavities. Their breathable construction effectively equalizes pressure while providing reliable protection from liquid submersion and dust contamination. Our product portfolio includes a range of materials and structures that meet the most challenging environmental demands and application needs.

For more information on acoustic vent technology, click over to gore.com/portableelectronics and see these articles:

Contact Gore to learn about the right GORE® Portable Electronic Vent for your unique application.


FOR INDUSTRIAL USE ONLY

Not for use in food, drug, cosmetic or medical device manufacturing, processing, or packaging operations.